1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

FF-22 Rcfoamfighters

Discussion in 'Single Wing Aircraft Plans' started by Galilee1986, Jan 30, 2010.

  1. Galilee1986

    Galilee1986 New Member

    Offline
    Messages:
    7
    Trophy Points:
    0
    Galilee1986, Jan 30, 2010
    #1
  2. Galilee1986

    Galilee1986 New Member

    Offline
    Messages:
    7
    Trophy Points:
    0
    Can any i tell me if its good?
     
    Galilee1986, Jan 30, 2010
    #2
  3. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Could you please upload the Sketchup file as well?
    Thank you
    Mark
     
    kram242, Jan 30, 2010
    #3
  4. Galilee1986

    Galilee1986 New Member

    Offline
    Messages:
    7
    Trophy Points:
    0
    Galilee1986, Jan 30, 2010
    #4
  5. theothers

    theothers Administrator Staff Member

    Offline
    Messages:
    761
    Trophy Points:
    18
    Location:
    New Jersey
    Thanks for the Sketchup files Galilee1986. We'll take a look at them and let you know what we think. It's great you are learning Sketchup and the Phlatscript now. By the time you get your Phlatprinter, you will be an expert :D

    Mark and Trish
     
    theothers, Jan 31, 2010
    #5
  6. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Ok I had a chance to mess around with this one a little and it looks good.
    There where a few changes I mad from looking at the PDF.
    I added a few more bend lines and did step cuts for the elevons
    I also deleted a few of the bridges/tabs that were not necessary.
    Other then that looks good Galilee1986 , keep up the good work and thank you for sharing this.
    Take a look at it and see what you think
    Mark and Trish Attached files FF22cnc_page1.cnc (13 KB)Â FF22cnc_page2.cnc (11.8 KB)Â RCFF F22.skp (435.6 KB)Â [​IMG]
     
    kram242, Jan 31, 2010
    #6
  7. Galilee1986

    Galilee1986 New Member

    Offline
    Messages:
    7
    Trophy Points:
    0
    Thanks kram !

    I'll study the mode you made. You should build this plane, he is reallly fast!

    I have a question : I know that your FFF is a bit longer than the foamboard (20x30) If i want to use a smaler sheet that the «safe area» can i ?

    Thanks again
     
    Galilee1986, Jan 31, 2010
    #7
  8. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Yes you can, all you have to do, is set up the safe cutting area in phlatscript parameters (20x30) and when you hit ok it will be the new safe cutting size you set.
    Then its just a mater of selecting the parts and putting them in there to fit the best you can.
    One way to make it a little easier is to select the parts one at a time and turn them into components so that you can easy move them around to get the position your after in the safe cutting area. Once you are done select them all and explode them and then your ready to output the new code :)
    This is one on the build list for me too :)
    Mark
     
    kram242, Jan 31, 2010
    #8
  9. Galilee1986

    Galilee1986 New Member

    Offline
    Messages:
    7
    Trophy Points:
    0
    I think that the scale is not good. I made the 3d plan in sketchup and I'm not sure...

    I'll check it
     
    Galilee1986, Feb 1, 2010
    #9

Share This Page