1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Search Results

Search Again
Page 1 of 2
  1. billm
    Thread

    Phlatprinter MKII for sale.

    I have a built Phlatprinter MKII minus the controller board and a complete printer (cabinets) with no electronics for sale. I built the MKII...
    Thread by: billm, Apr 1, 2017, 2 replies, in forum: Used Phlatprinters FORSALE
  2. billm
    Post

    Don't See Any Voltage on TP1

    One of the boards has the posts and one doesn't. Not a biggie. The X has to be set to 4v for the drum to turn smoothly. I'm guessing the motor...
    Post by: billm, Jul 3, 2010 in forum: Trouble Shooting - Support - Help Section
  3. billm
    Post

    Don't See Any Voltage on TP1

    That's what I did and I didn't get any reading on any of the test points. There's an issue with the X drive - doesn't have enough torque to spin...
    Post by: billm, Jul 2, 2010 in forum: Trouble Shooting - Support - Help Section
  4. billm
    Post

    Don't See Any Voltage on TP1

    Thanks. I have a new board that I haven't used yet and I just looked at it. It doesn't have the posts either. The component layouts are also...
    Post by: billm, Jul 2, 2010 in forum: Trouble Shooting - Support - Help Section
  5. billm
    Thread

    Don't See Any Voltage on TP1

    I'm troubleshooting a Phlatprinter that belongs to someone else. It is a an orig. Phlatprinter with a lot of mods, including the belt mod.. The...
    Thread by: billm, Jul 2, 2010, 6 replies, in forum: Trouble Shooting - Support - Help Section
  6. billm
    Post

    Can't trace imported outline

    I think I have it figured out :P
    Post by: billm, Jun 17, 2010 in forum: Sketchup Tutorials
  7. billm
    Post

    Can't trace imported outline

    Thanks, it is set to 1/64", I also tried turning off angle snapping. It didn't make any difference.
    Post by: billm, Jun 17, 2010 in forum: Sketchup Tutorials
  8. billm
    Thread

    Can't trace imported outline

    I'm trying to learn Sketchup and I have run into a problem that probably has a simple solution. But I've spent almost 2 hours trying to figure it...
    Thread by: billm, Jun 17, 2010, 4 replies, in forum: Sketchup Tutorials
  9. billm
    Post

    Hobby Central Phlatprinter II Complete

    Well so far she has found hardened glue on the floor tiles and on a seat cushion on one of the chairs. She's taken it in good stride so far. I...
    Post by: billm, May 27, 2010 in forum: Phlatprinter MKII BUILD LOGS
  10. billm
    Post

    Foam Safe Paint

    I have airbrushes and acrylic paint - it takes too long with the clean up. LOL.
    Post by: billm, May 26, 2010 in forum: Foam Talk
  11. billm
    Thread

    Foam Safe Paint

    I'm having a hard time finding foam safe spray paint. I went by the local Hobby Lobby, as in the past I bought silver foam safe spray there....
    Thread by: billm, May 26, 2010, 4 replies, in forum: Foam Talk
  12. billm
    Post

    woo hoo new supply of FFF at our Lowes

    We have 3 Lowes and they all have pallets of FF - but it's $39.99 a bundle. Last time I bought it ( a lonnnggg time ago) it was $27. Bill Hobby...
    Post by: billm, May 26, 2010 in forum: Foam Talk
  13. billm
    Post

    Hobby Central Phlatprinter II Complete

    ToxicToast, my main problem was definetly the drive roller - Mark Trish sent me another one. I did the spiral wrap on it and it worked fine....
    Post by: billm, May 25, 2010 in forum: Phlatprinter MKII BUILD LOGS
  14. billm
    Post

    Hobby Central Phlatprinter II Complete

    I jumped the gun a little bit. It is missing lines from the cut outs. I'm going to play with it and see what happens.
    Post by: billm, May 22, 2010 in forum: Phlatprinter MKII BUILD LOGS
  15. billm
    Post

    Hobby Central Phlatprinter II Complete

    Well, I received the replacement parts yesterday and installed them today. I'm cutting my second test plane right now and everything looks good...
    Post by: billm, May 21, 2010 in forum: Phlatprinter MKII BUILD LOGS
  16. billm
    Post

    Hobby Central Phlatprinter II Complete

    Mark I'm out for the day and I've been trying to pm u without sucess from my iPhone I will email you tonight as I want to order a bunch of stuff...
    Post by: billm, May 2, 2010 in forum: Phlatprinter MKII BUILD LOGS
  17. billm
    Post

    Hobby Central Phlatprinter II Complete

    Yeah, I think for whatever reason the roller is out of round and it is just enough to lose sufficient contact to move the material. I thought...
    Post by: billm, May 2, 2010 in forum: Phlatprinter MKII BUILD LOGS
  18. billm
    Post

    Hobby Central Phlatprinter II Complete

    No I didn't add anything, but it may be just too low. I will try shimming it up tomorrow. Bill
    Post by: billm, May 2, 2010 in forum: Phlatprinter MKII BUILD LOGS
  19. billm
    Post

    Hobby Central Phlatprinter II Complete

    I tried cutting out a test project, but it slipped half way through the cut. I'll have to take another look at the drum tomorrow. Bill Hobby Central
    Post by: billm, May 1, 2010 in forum: Phlatprinter MKII BUILD LOGS
  20. billm
    Post

    Hobby Central Phlatprinter II Complete

    3DMON, it might very be out of round as it does catch except for about an inch. I've calibrated it and checked it several times right now - with...
    Post by: billm, May 1, 2010 in forum: Phlatprinter MKII BUILD LOGS
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2