1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Search Results

Search Again
Page 1 of 3
  1. Darwin
    Thread

    First Push-E Cat V5 Fuselage Cut

    Hey Guys: My biggest motivation for getting a Phlatprinter has finally come to reality. Today, I successfully cut the front part of the Push-E...
    Thread by: Darwin, Dec 21, 2011, 6 replies, in forum: Projects on your Phlatprinter 3
  2. Darwin
    Post

    Note: Bit Square to Cut Surface

    Another way to check and see if you have an issue is to look at the sides of your cuts that are either X or Y straight. If there's an angle to the...
    Post by: Darwin, Dec 13, 2011 in forum: General Phlatprinter 3 Chat
  3. Darwin
    Post

    Note: Bit Square to Cut Surface

    I haven't actually run the unit yet. I will do some air cuts and listen to things to see if I need to change the voltage setting. I already run a...
    Post by: Darwin, Dec 13, 2011 in forum: General Phlatprinter 3 Chat
  4. Darwin
    Post

    Working on a Christmas present for the phlatprinter owners

    I like it. Don't care much for Depron, but I like the looks of this bird. Good job!
    Post by: Darwin, Dec 7, 2011 in forum: Single Wing Aircraft Plans
  5. Darwin
    Post

    I come to the conclusion of no solution

    Back in the day at Navistar, the techs in the pattern shop rigged up compressed air lines to the 5-axis router whenever they cut Renboard parts....
    Post by: Darwin, Dec 7, 2011 in forum: Phlatprinter 3 Attachments
  6. Darwin
    Thread

    Note: Bit Square to Cut Surface

    One thing you might want to check when you're setting up your machines is the squareness of the bits to the drive rollers. I'd never really...
    Thread by: Darwin, Dec 7, 2011, 5 replies, in forum: General Phlatprinter 3 Chat
  7. Darwin
    Post

    Mr Mulligan

    That is impressive as all get out. Excellent job!
    Post by: Darwin, Dec 4, 2011 in forum: * Scratch Built Section *
  8. Darwin
    Post

    Positron II First EPP Cut

    I'm going to start a new thread in the PP /// troubleshooting forum. It's my fault for drifting the conversation from "New Projects". The...
    Post by: Darwin, Oct 24, 2011 in forum: Projects on your Phlatprinter 3
  9. Darwin
    Post

    Positron II First EPP Cut

    Okay, had a great conversation with Mark today. Gotta love his and Trish' commitment to customer service. Considering all that's had to be faced...
    Post by: Darwin, Oct 24, 2011 in forum: Projects on your Phlatprinter 3
  10. Darwin
    Post

    Positron II First EPP Cut

    I inserted a Y-step command into my test file and used the Sharpie attachment to generate a visible map of the continued X-axis issues. This was...
    Post by: Darwin, Oct 23, 2011 in forum: Projects on your Phlatprinter 3
  11. Darwin
    Post

    Positron II First EPP Cut

    Yoram: Idlers are turning. I'll check them with the belt off to assess binding. I have also been contemplating installing bearings in them, but...
    Post by: Darwin, Oct 23, 2011 in forum: Projects on your Phlatprinter 3
  12. Darwin
    Post

    Positron II First EPP Cut

    The pulley on my X-axis has the plastic cog with an aluminum hub that the set screw is threaded through. Is this the right one? I noticed that...
    Post by: Darwin, Oct 23, 2011 in forum: Projects on your Phlatprinter 3
  13. Darwin
    Post

    Positron II First EPP Cut

    Fun not happening. The Phlatty is exhibiting extreme unreliability along the X-axis due to skipped steps. Wasn't obvious when cutting the first...
    Post by: Darwin, Oct 22, 2011 in forum: Projects on your Phlatprinter 3
  14. Darwin
    Post

    Positron II First EPP Cut

    Writing the instructions now. I need to set up a router template for the wings to cut the main spar slots (very narrow, so I can't cut them on the...
    Post by: Darwin, Oct 5, 2011 in forum: Projects on your Phlatprinter 3
  15. Darwin
    Post

    Positron II First EPP Cut

    There's actually two CF spars in the wing, CF ribbons in the control surfaces, and CF guys supporting the rudder. The push rods in this prototype...
    Post by: Darwin, Oct 5, 2011 in forum: Projects on your Phlatprinter 3
  16. Darwin
    Post

    Positron II First EPP Cut

    [img] Okay, so here's the finished product. I'm setting up with Du-Bro right now to get all the hardware the kits need. I flew it yesterday...
    Post by: Darwin, Oct 5, 2011 in forum: Projects on your Phlatprinter 3
  17. Darwin
    Thread

    Positron II First EPP Cut

    Hey Guys: A while back I cut a Positron II proof-of-concept proto out of 1/4" fan-fold. It flew well enough for me having forgotten to support...
    Thread by: Darwin, Sep 16, 2011, 19 replies, in forum: Projects on your Phlatprinter 3
  18. Darwin
    Post

    Doing router tooling with my PP///

    Thanks for the encouragement, Mark. I reviewed the piece in the picture a bit more closely last night. It looks like the X was drifting negative...
    Post by: Darwin, Sep 11, 2011 in forum: Projects on your Phlatprinter 3
  19. Darwin
    Post

    I come to the conclusion of no solution

    I've been considering wrapping a coil of bare copper solid wire around the rollers on the drive end of the unit and running it back to ground on...
    Post by: Darwin, Sep 10, 2011 in forum: Phlatprinter 3 Attachments
  20. Darwin
    Thread

    Doing router tooling with my PP///

    Hey Folks: I've had a long and arduous trip with my PP ///, but I've finally gotten things to the point where I'm getting utility out of it. I'm...
    Thread by: Darwin, Sep 10, 2011, 2 replies, in forum: Projects on your Phlatprinter 3
Showing results 1 to 20 of 42 Next >
Search Again
Page 1 of 3