1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Recent Content by BArnold

  1. BArnold
    Thread

    Sure Is A Lot Of Spam On Here!

    Seems like most of the recent posts have nothing to do with the subject of this forum.
    Thread by: BArnold, May 27, 2015, 3 replies, in forum: General Talk Forum
  2. BArnold
    Post

    Success (partly) With 3D

    The UGS plotter shows almost half the last section not getting cut. Yet, I don't see anything in the gcode that should have caused it to jump to...
    Post by: BArnold, May 23, 2015 in forum: SketchUcam Help
  3. BArnold
    Thread

    Success (partly) With 3D

    I drew a simple rosette in SketchUp 2015 and, after a few trials, got 3d gcode generated with SketchUcam. Overall, it seemed to work but there...
    Thread by: BArnold, May 22, 2015, 2 replies, in forum: SketchUcam Help
  4. BArnold
    Post

    Project Cut Undersize

    OK - did another test drawing this morning. It had been drilled into me by a certified SketchUp trainer that the working face of an object should...
    Post by: BArnold, May 21, 2015 in forum: SketchUcam Bugs
  5. BArnold
    Post

    Invert Z

    I'm new to this and curious. What is different about your CNC that would require the Z-axis to be reversed?
    Post by: BArnold, May 20, 2015 in forum: SketchUcam 'Most wanted Feature'
  6. BArnold
    Post

    Project Cut Undersize

    I'm using the "Woodworking - Inches" template and the "Woodworking" option in "Default Styles". You're correct about the visible face of a...
    Post by: BArnold, May 20, 2015 in forum: SketchUcam Bugs
  7. BArnold
    Post

    Project Cut Undersize

    Well, color me a bit embarrassed! I see what you mean about the different color lines and I know how I got there. When setting up my drawing, as...
    Post by: BArnold, May 20, 2015 in forum: SketchUcam Bugs
  8. BArnold
    Post

    Project Cut Undersize

    As a further test, I set up my table saw insert in Inkscape and imported the SVG into Makercam to make my toolpaths. When I ran it, the insert...
    Post by: BArnold, May 19, 2015 in forum: SketchUcam Bugs
  9. BArnold
    Post

    Project Cut Undersize

    I copied the code you posted, pasted it into Wordpad, and modified it for a 1/8" end mill bit. When I ran the code below, I got a rectangle that...
    Post by: BArnold, May 19, 2015 in forum: SketchUcam Bugs
  10. BArnold
    Post

    Project Cut Undersize

    Here are my files:
    Post by: BArnold, May 19, 2015 in forum: SketchUcam Bugs
  11. BArnold
    Thread

    Project Cut Undersize

    Over the past couple weeks, I've been spending a lot of time tweaking the calibration of my SO2. I've run some Square-Circle-Triangle cuts using...
    Thread by: BArnold, May 18, 2015, 13 replies, in forum: SketchUcam Bugs
  12. BArnold
    Post

    SletchUcam/SketchUp2015 Errors

    @marcomartim: I made the change you showed and the detail shows in my drawing now when I have SUCam loaded. I also found another color that was...
    Post by: BArnold, Apr 30, 2015 in forum: SketchUcam Bugs