1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Search Results

Search Again
Page 9 of 9
  1. Jnida63
    Post

    Tribute 4D - Nitro plane

    I would use carbon fiber for the leading edge also and a carbon fiber towards the back where the back hole comes to a point. That should sturdy up...
    Post by: Jnida63, Mar 7, 2009 in forum: * Scratch Built Section *
  2. Jnida63
    Post

    Tab depths gone goofy

    Nope, it was a bug in the script. blew out the folder and re-installed and it's fine now
    Post by: Jnida63, Mar 1, 2009 in forum: SketchUcam Help
  3. Jnida63
    Thread

    Tab depths gone goofy

    My Z axis is working fine but none of my tabs are going %50 thru the material anymore and my centerline and fold cuts aren't getting cut either....
    Thread by: Jnida63, Mar 1, 2009, 2 replies, in forum: SketchUcam Help
  4. Jnida63
    Post

    Talk it up about the MKII

    I love my original and don't really care about the speed as i am not selling anything or trying to make money off it. I really, really like the...
    Post by: Jnida63, Feb 27, 2009 in forum: GENERAL Phlatprinter MKII Talk
  5. Jnida63
    Post

    Crash's Edge 540, 32 and 40

    Hey Crash, I love the plane and I took some liberties with it, I hope you don't mind but I am working it up as a full fuse version, if you don't...
    Post by: Jnida63, Feb 27, 2009 in forum: Single Wing Aircraft Plans
  6. Jnida63
    Post

    Cutting Depron

    I was actually thinking of cutting a square out of some Bluecore 15" X 39" and taping the depron inside it for maximum width grip. I only have 10...
    Post by: Jnida63, Feb 22, 2009 in forum: Trouble Shooting - Support - Help Section
  7. Jnida63
    Post

    Cutting Depron

    It is the 15" X 39" 6MM stuff RcFoam sells, I will try the centering thing. I just have to adjust everything in Sketchup now(
    Post by: Jnida63, Feb 22, 2009 in forum: Trouble Shooting - Support - Help Section
  8. Jnida63
    Post

    Cutting Depron

    I am using the 6mm from rcfoam.com, I might try running a piece of masking tape down each side. The stuff is too expensive to keep messing up
    Post by: Jnida63, Feb 22, 2009 in forum: Trouble Shooting - Support - Help Section
  9. Jnida63
    Thread

    Cutting Depron

    Is there a trick to cutting Depron? When I run a sheet thru it seems to get stuck and the drive rollers just cut a gouge into it. Any tips so that...
    Thread by: Jnida63, Feb 22, 2009, 6 replies, in forum: Trouble Shooting - Support - Help Section
  10. Jnida63
    Post

    yarsmythejr's Funder Lightning

    Read this post about the K-F airfoil on bottom http://www.rcgroups.com/forums/showthre ... t=fogleman
    Post by: Jnida63, Feb 18, 2009 in forum: * Scratch Built Section *
  11. Jnida63
    Post

    yarsmythejr's Funder Lightning

    I had one I hand cut and it flew nicely. I did mess up on the size of the K-F wing size, I will fix that. From everything i have seen on the K-F...
    Post by: Jnida63, Feb 18, 2009 in forum: * Scratch Built Section *
  12. Jnida63
    Post

    yarsmythejr's Funder Lightning

    I wasn't asking anyone to do the work for me, I was asking for pointers on which way to go about it. I think I have it figured out, test cut is...
    Post by: Jnida63, Feb 17, 2009 in forum: * Scratch Built Section *
  13. Jnida63
    Thread

    yarsmythejr's Funder Lightning

    Ok, i redrew this in Sketchup but i have no idea how to break it all down to make it a cuttable file. Any help would be appreciated....
    Thread by: Jnida63, Feb 16, 2009, 11 replies, in forum: * Scratch Built Section *
Find older messages
Showing results 161 to 173 of 173
Search Again
Page 9 of 9